*Actual product and finish may vary
AL600ULACM Altronix converts a 115VAC 60Hz input into eight (8) independently controlled 12VDC or 24VDC Fail-Safe and/or Fail-Secure outputs with a total of 6 amp continuous supply current.
These power outputs can be converted to dry form "C" contacts. Outputs
are activated by an open collector sink or normally open (NO) dry
trigger input from an Access Control System, Card Reader, Keypad, Push
Button, PIR, etc. This unit will route power to a variety of access
control hardware devices including Mag Locks, Electric Strikes, Magnetic
Door Holders, etc. The outputs will operate in both Fail-Safe and/or
Fail-Secure modes. This unit is designed to be powered by one common
power source (factory installed) which will provide power for both the
board operation and locking devices, or two (2) totally independent
power sources, one (1) providing power for board operation and the other
for lock / accessory power. The FACP Interface enables Emergency
Egress, Alarm Monitoring, or may be used to trigger other auxiliary
devices. The fire alarm disconnect feature is individually selectable
for any or all of the eight (8) outputs.
Input:
Input 115VAC 60Hz rated @ 3.5 amp.
Power supply input options:
a) One (1) common power input for ACM8/ACM8CB and lock power (factory installed).
b) Two (2) isolated power inputs - One (1) to power the ACM8/ACM8CB and one (1) for lock accessory power, (external power supply is required). (Current is determined by the power supply connected, not to exceed a maximum of 10 amp total).
Eight (8) Access Control System trigger inputs.
Input options:
a) Eight (8) normally open (NO) inputs.
b) Eight (8) open collector inputs.
c) Any combination of the above.
Output:
12VDC or 24VDC @ 6 amp supply current.
Eight (8) independently controlled outputs.
Output options:
a) Eight (8) Fail-Safe and/or Fail-Secure power outputs.
b) Eight (8) form "C" 5 amp rated relay outputs
c) Any combination of the above.
Eight (8) auxiliary power outputs (unswitched)
Output ratings:
- Fuses are rated @ 3.5 amp.
Filtered and electronically regulated outputs (built-in power supply).
Features:
Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
Fire Alarm disconnect input options:
a) Normally open (NO) or normally closed (NC) dry contact input.
b) Polarity reversal input from FACP signaling circuit.
Alarm output relay indicates that FACP input is triggered (form "C" contact rated @ 1 amp 28VDC).
Short circuit and thermal overload protection.
AC fail supervision (form "C" contact).
Visual Indicators:
Red LEDs indicate outputs are triggered (relays energized).
Green LED indicates FACP disconnect is triggered.
AC input and DC output LED indicators.
Battery Backup:
Built-in charger for sealed lead acid or gel type batteries.
AL600ULB (Power Supply Board) maximum charge current 0.7 amp.
Automatic switch over to stand-by battery when AC fails.
Zero voltage drop when unitswitches over to battery backup (AC failure condition).
Battery fail and battery presence supervision (form "C" contact).
Electrical:
Operating temperature: 0° C to 49° C ambient.
ACM8 board main fuse is rated at 10 amp.
BTU/Hr.:
- 12VDC: 36.85BTU/Hr.
- 24VDC: 73.70BTU/Hr
Input:
Input 115VAC 60Hz rated @ 3.5 amp.
Power supply input options:
a) One (1) common power input for ACM8/ACM8CB and lock power (factory installed).
b) Two (2) isolated power inputs - One (1) to power the ACM8/ACM8CB and one (1) for lock accessory power, (external power supply is required). (Current is determined by the power supply connected, not to exceed a maximum of 10 amp total).
Eight (8) Access Control System trigger inputs.
Input options:
a) Eight (8) normally open (NO) inputs.
b) Eight (8) open collector inputs.
c) Any combination of the above.
Output:
12VDC or 24VDC @ 6 amp supply current.
Eight (8) independently controlled outputs.
Output options:
a) Eight (8) Fail-Safe and/or Fail-Secure power outputs.
b) Eight (8) form "C" 5 amp rated relay outputs
c) Any combination of the above.
Eight (8) auxiliary power outputs (unswitched)
Output ratings:
- Fuses are rated @ 3.5 amp.
Filtered and electronically regulated outputs (built-in power supply).
Features:
Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
Fire Alarm disconnect input options:
a) Normally open (NO) or normally closed (NC) dry contact input.
b) Polarity reversal input from FACP signaling circuit.
Alarm output relay indicates that FACP input is triggered (form "C" contact rated @ 1 amp 28VDC).
Short circuit and thermal overload protection.
AC fail supervision (form "C" contact).
Visual Indicators:
Red LEDs indicate outputs are triggered (relays energized).
Green LED indicates FACP disconnect is triggered.
AC input and DC output LED indicators.
Battery Backup:
Built-in charger for sealed lead acid or gel type batteries.
AL600ULB (Power Supply Board) maximum charge current 0.7 amp.
Automatic switch over to stand-by battery when AC fails.
Zero voltage drop when unitswitches over to battery backup (AC failure condition).
Battery fail and battery presence supervision (form "C" contact).
Electrical:
Operating temperature: 0° C to 49° C ambient.
ACM8 board main fuse is rated at 10 amp.
BTU/Hr.:
- 12VDC: 36.85BTU/Hr.
- 24VDC: 73.70BTU/Hr