For Doors: Wood/metal. 1-3/4" (44.5mm) minimum thickness. 4-1/2" (114mm) minimum stile width.

Chassis: Nonferrous alloy.

Chassis Cover: Non-ferrous plated material.

End Cap: Brass, Bronze or Stainless Steel construction.

Handing: Handed. Specify RHR or LHR.

ANSI Standard: A156.3, Grade 1.

Mounting: Furnished standard with wood and machine screws.

Strikes: Standard ANSI strike.

Mortise Lock: Grade (1) for 1-3/4" (44.5mm) thick doors. Reversible. Fits door prepared for ANSI Standard A115.1.

Trim: See Trim Designs section.

Electric Functions: (ELR) Electrical Latch Retraction and RX & LX Signal Switch available.

Door Size: MR9800EO36 for 36" doors. MR9800EO48 for 48" doors.

Alarm: Prefix "NALRM" before PART#

Additional Accessories:

Exit Alarm: Add Prefix NALRM, Example NALRM9800

MUST ORDER CR602RF or CR631RF POWER SUPPLY TO HONOR WARRANTY AND UL MARKING

Our electrified latch pullback exit device allows for remote keyless access control in high occupancy/high traffic conditions where exit devices are required. Common applications include conditions such as hospitals, airports, schools, churches and where they are commonly specified in applications that require automatic door openers. The device may be continuously energized allowing for a push/pull condition if desired.

Features:

Available on 9800, 7700 & 2200 Series, including rim, vertical rod, concealed vertical rod, mortise exit device, fire

and non fire-rated devices. - High-performance quality solenoids designed for demanding applications.

The PM200* interface power module (included) is programmed to meet the requirements of the specific exit device

modification. It maximizes the efficiency and life of the solenoid, allows for a much longer wire run and may be

used with 24VDC power supplies rated at 1.5A or greater - Dual coil solenoids, or PWM programming, allow for either momentary or extended time latch retraction.

No hassle 3-Year Warranty

Specifications:

Voltage – 24VDC

 Amperage – Surge current – 12A for 200ms@24V / Holding – 250mA@24V

Coil resistance – 3.7 Ohms

To Order, Specify:

Prefix ELR before PART#

ITEM #                   DESCRIPTION

ELR                        Electrified Latch Retractor

Signal Switch RX and LX

RX (request to exit) signal switch is used to signal the use of an opening from the push side. When the push pad is depressed, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch that monitors the touch bar.

LX (latch bolt monitoring) signal switch monitors both egress and access of an opening. When the latch bolt is retracted, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch that monitors the latch bolt position.

LX and RX switches can be combined with EL (electric latch retraction) option.

Specifications:

RX or LX............................... Switch rated 0.5 amperes @ 24VAC/DC resistive

Low current RX or LX........... Switch rated 0.5 amperes @ 24VAC/DC resistive

For Factory Installed:

To Order, Specify:

Prefix:

RX.......................Request to Exit

LX........................ Latch bolt Monitoring

LXRX................... Latch bolt Monitoring/Request to Exit Combination

ITEM #                                   DESCRIPTION

RX                           Request to Exit switch for field installation.

LX                           Latch bolt Monitoring switch for field installation.

LXRX                      Latch bolt Monitoring/Request to Exit Combination

Specify : 7700, 9800 or 2200 after ITEM# when ordering, for example: RX7700 to order RX switch for 7700 series exit devices