*Actual product and finish may vary

AF9800EO36 Cal-Royal Fire Rated Rim Exit Device 36" - Exit Only - Fits same hole pattern as Sargent 8800 Series using 9800 Escutcheon Trims

Meets The Buy American Act

Lifetime Warranty

Cal-Royal is also in compliance with the Buy American Act as well as the American Recovery and Reinvestment Act of 2009.

Model Actual Size Max.Cut Down Door Size

AF9800EO36 32” 6” 30” to 36” door width

AF9820EO48 44” 12” 36” to 48” door width

ANSI A156.3, Grade 1 Heavy Duty Exit Device in surface vertical rod and rim designs. - UL listed for panic and ULC10C, UBC 7-2-1997 Codes. - UL Listed for Fire Exit Hardware. 3 Hours.

Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad. End caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing.

BHMA Certified

Lifetime Warranty

Chassis mounted unit construction. Rim and vertical rod devices are non-handed and easily reversible.

Lever and escutcheon trims are Grade 1 construction with Clutch Freewheeling Mechanism.

Optional Mullion and Alarm.

Features & Construction

Retrofits Sargent 8800 Series using 9800 Escutcheon Trim

ANSI A156.3, Grade 1 heavy duty exit device in surface vertical rod and rim designs

Rail assemblies and end caps are brass, bronze or stainless steel and rail travels in direction of the door swing.

Trims are thru bolted for additional security.

Conforms & meets ADA Regulations.

UL Listed for Panic and UL10C, UBC 7-2-1997 codes.

UL Listed for Fire Exit Hardware. 3 hours.

(A) label rating on pairs of doors up to 8’0” x 8’0” swinging in same or opposite directions.

Uncompromising security and safety in single and double fire exit doors.

Chassis mounted unit construction. Rim and vertical rod devices are non-handed and easily reversible.

Available in many different functions. Lever and escutcheon trims are grade 1 construction with clutch on rose trims. Escutcheon trims are rigid and covers 161 cut out.

Additional Accessories:

Exit Alarm: Add Prefix NALRM, Example NALRM9800

MUST ORDER CR602RF or CR631RF POWER SUPPLY TO HONOR WARRANTY AND UL MARKING

Our electrified latch pullback exit device allows for remote keyless access control in high occupancy/high traffic conditions where exit devices are required. Common applications include conditions such as hospitals, airports, schools, churches and where they are commonly specified in applications that require automatic door openers. The device may be continuously energized allowing for a push/pull condition if desired.

Features:

Available on 9800, 7700 & 2200 Series, including rim, vertical rod, concealed vertical rod, mortise exit device, fire

and non fire-rated devices. - High-performance quality solenoids designed for demanding applications.

The PM200* interface power module (included) is programmed to meet the requirements of the specific exit device

modification. It maximizes the efficiency and life of the solenoid, allows for a much longer wire run and may be

used with 24VDC power supplies rated at 1.5A or greater - Dual coil solenoids, or PWM programming, allow for either momentary or extended time latch retraction.

No hassle 3-Year Warranty

Specifications:

Voltage – 24VDC

Amperage – Surge current – 12A for 200ms@24V / Holding – 250mA@24V

Coil resistance – 3.7 Ohms

To Order, Specify:

Prefix ELR before PART#

ITEM # DESCRIPTION

ELR Electrified Latch Retractor

Signal Switch RX and LX

RX (request to exit) signal switch is used to signal the use of an opening from the push side. When the push pad is depressed, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch that monitors the touch bar.

LX (latch bolt monitoring) signal switch monitors both egress and access of an opening. When the latch bolt is retracted, the switch is activated. These devices are equipped with an internal SPDT (single pole double throw) switch that monitors the latch bolt position.

LX and RX switches can be combined with EL (electric latch retraction) option.

Specifications:

RX or LX............................... Switch rated 0.5 amperes @ 24VAC/DC resistive

Low current RX or LX........... Switch rated 0.5 amperes @ 24VAC/DC resistive

For Factory Installed:

To Order, Specify:

Prefix:

RX.......................Request to Exit

LX........................ Latch bolt Monitoring

LXRX................... Latch bolt Monitoring/Request to Exit Combination

ITEM # DESCRIPTION

RX Request to Exit switch for field installation.